en
Englishen中文(繁体)zh-TWDeutschde

Custom Thermal Pads Manufacturer for OEM Electronics, EV & Industrial Applications

We manufacture custom silicone thermal pads and thermally conductive silicone components built to your drawing, 3D file, thermal requirement and production volume. LSRParts supports OEMs, Tier suppliers and engineering teams from material selection and DFM review to tooling, sampling, mass production, inspection and packaging.

If you need production-ready thermal pads for electronics, battery systems, sensors, power modules or industrial assemblies, send us your drawing or application requirements for an RFQ.

Request a Thermal Pad RFQ

Custom Thermal Pads Built Around Your Application

LSRParts focuses on custom silicone components, not standard off-the-shelf rubber products. For thermal pads, we help customers balance:

  • ● Thermal conductivity
  • ● Compression and rebound
  • ● Shore hardness
  • ● Gap-filling performance
  • ● Dielectric insulation
  • ● Thickness tolerance
  • ● Surface tack
  • ● Flame-retardant requirements
  • ● Long-term reliability
  • ● Production repeatability

Our thermal pads are suitable for applications where heat transfer, dimensional consistency and stable production matter.

Custom thermal pads for OEM electronics and EV applications

Typical applications include:

EV battery packs and battery management systems
Power electronics and inverters
LED lighting modules
Sensors and control units
Telecom and industrial electronics
Automotive electronic modules
Consumer and commercial devices
Heat sinks, housings and PCB assemblies

What We Manufacture

We produce custom thermal pads using silicone-based and thermally conductive silicone materials, with manufacturing routes selected according to part geometry, tolerance, annual demand and performance requirements.

Product Type Typical Use
Silicone thermal pads Gap filling between heat source and heat sink
Thermally conductive silicone pads Electronics, automotive and power modules
Die-cut thermal interface pads High-volume repeatable pad geometries
Molded thermal silicone parts 3D features, bosses, ribs, lips or sealing functions
Overmolded thermal silicone components Silicone bonded to plastic or metal substrates
Custom thermal gaskets Combined sealing and heat-transfer requirements
Thermally conductive silicone strips Continuous or cut-to-length applications

Why OEM Buyers Work With LSRParts

A thermal pad is often a small part inside a much larger system, but failure can cause overheating, assembly problems or field reliability issues. We support B2B customers who need a stable manufacturing partner for repeat production.

We are a good fit when your project has:

  • ✓ Custom drawings, 3D files or defined application requirements
  • ✓ New tooling or die-cutting requirements
  • ✓ Prototype-to-mass-production roadmap
  • ✓ Annual demand above 100,000 pcs
  • ✓ Thermal, sealing, electrical or compression requirements
  • ✓ Tight thickness or profile tolerance requirements
  • ✓ Need for DFM, material selection and validation support

Our priority

High-value, repeat-production silicone components rather than low-volume commodity pads.

Note: We are not a fit for one-off or low-volume commodity thermal pad purchases.

Thermal Pad Manufacturing Capabilities

Depending on the design, we can manufacture thermal pads and related components using compression molding, LSR molding, overmolding, extrusion and secondary operations such as die cutting, slitting, trimming and inspection.

Silicone Compression Molding

Compression molding is commonly used for silicone pads, sheets, gaskets and larger thermally conductive silicone parts.

Parameter LSRParts Capability
ProcessSilicone Rubber Compression Molding
Maximum Size2500 × 2000 × 1000 mm
Typical Part Tolerance±0.2 mm
Small Part Mold Cavity Tolerance±0.1–0.2 mm
Complex Part Mold Cavity Tolerance±0.3–0.5 mm
Part-to-Part RepeatabilityApprox. ±0.1 mm
CavitiesSingle / Multi-cavity
Mold LifeUp to 3–5 million shots, application dependent
Mold MaterialsP20 / H13 / 420 Stainless Steel
Secondary OperationsPost-cure, trimming, punching, drilling, printing, bonding, assembly

LSR Injection Molding

For 3D thermal silicone components or parts requiring precision geometry, LSR injection molding may be used.

Parameter LSRParts Capability
ProcessLiquid Silicone Rubber Injection Molding
Maximum Part Envelope300 × 200 × 100 mm
Silicone Hardness10–80 Shore A
Typical Part Tolerance±0.05 mm
Critical ToleranceDown to ±0.02 mm, application dependent
Mold Manufacturing Tolerance±0.01 mm
Mold CavitiesSingle-cavity / Multi-cavity
Production Mold Life3–5 million shots, tooling/application dependent
Tooling TypePrototype Tooling / Production Tooling
Production ScalePrototype to high-volume mass production
Secondary OperationsPost-curing, trimming, printing, laser marking, bonding, assembly

Silicone Extrusion

For thermal silicone strips, continuous profiles or cut-to-length pads, extrusion may be suitable.

Parameter LSRParts Capability
ProductsTubing, cords, strips, custom profiles, multi-lumen tubing
Tubing / Profile OD0.5–120 mm
Standard Cross-Section Tolerance±0.05 mm
Precision Cross-Section Tolerance±0.03 mm
Wall Thickness0.3–15 mm
LengthCut-to-length / Continuous coils
Maximum Continuous CoilUp to 1,000 m
SurfaceSmooth / Matte / Textured / Fabric impression
ColorPantone / RAL matching
Production VolumePrototype to 1M+ meters/year
Secondary OperationsCutting, coiling, joining, marking, inspection, packaging

Thermally Conductive Silicone Material Support

We help select silicone materials according to thermal, mechanical, electrical and environmental requirements.

Material Target Applications
Thermally Conductive SiliconeThermal management
Electrically Conductive SiliconeElectronics / EMI
Flame-Retardant SiliconeElectrical / automotive
High-Temperature SiliconeAutomotive / industrial
Low-Temperature SiliconeOutdoor / automotive
General Purpose LSRIndustrial / electronics
Medical Grade LSRMedical devices
Food Grade LSRFood / beverage / baby
Platinum-Cured SiliconeMedical / food contact
FluorosiliconeAutomotive / fuel / chemical exposure
Custom CompoundsApplication specific

For RFQ review, we can work with your specified material, recommended grade or performance targets such as hardness, thermal conductivity, operating temperature, color, flame rating or insulation requirement.

DFM Review Before Tooling

A reliable thermal pad starts before production tooling is built. Our engineering team reviews the part and application to identify manufacturing risks early.

For thermal pads, our DFM review may include:

  • ✓ Thickness and compression range
  • ✓ Flatness and dimensional control
  • ✓ Molded vs. die-cut manufacturing route
  • ✓ Hole, slot and edge geometry
  • ✓ Flash requirement
  • ✓ Surface tack or release liner requirement
  • ✓ Hardness and rebound behavior
  • ✓ Assembly method
  • ✓ Thermal path and contact area
  • ✓ Tolerance stack-up in the final assembly
  • ✓ Annual volume and tooling strategy

This helps customers move from prototype validation to stable production with fewer surprises.

Prototype to Mass Production Workflow

DFM Review → Material Selection → Mold Design → Tool Manufacturing → T0/T1 Sampling → Validation → Production Approval → Mass Production → Inspection → Assembly & Packaging

We can support early engineering builds, pilot runs and high-volume production programs.

Tooling for Custom Thermal Pads

We manufacture prototype and production tooling based on the required production volume and part complexity.

Tooling Capability Specification
DFMYes
CADSolidWorks / CAD
Mold Flow ReviewSupported
CNC3-axis / 5-axis CNC
EDMSinker EDM / Wire EDM
Rapid ToolingAluminum tooling
Rapid Tool LifeApprox. 100–10,000 cycles
Production ToolingHardened steel tooling
Common Mold SteelP20 / NAK80 / H13 / S136 / 420
Aluminum Tooling6061 / 7075
Tool Surface FinishRa 0.8 µm or better where required
Prototype Tool Lead TimeBenchmark approx. 10–12 days
Production Tool Lead TimeBenchmark approx. 3–6 weeks
SamplingT0 / T1 / validation
Multi-Cavity ToolingYes
High-Volume ToolingYes

Secondary Operations for Thermal Pads

We provide secondary processing to deliver thermal pads ready for assembly.

Secondary Operation Supported
Post-Curing✓
Precision Trimming✓
Die Cutting✓
Punching✓
X / Y Slitting✓
Laser Marking✓
Pad Printing✓
Silk Screening✓
Drilling✓
Bonding✓
Cutting & Coiling✓
Assembly✓
Functional Testing✓
Inspection✓
Custom Packaging✓

Secondary operations may include custom liner handling, part identification, kitting, assembly support and packaging according to your production line requirements.

Industries We Serve

Automotive & EV

We manufacture silicone thermal pads and thermal management components for EV batteries, power electronics, sensors and control modules.

Typical parts include:

  • ● Battery thermal interface pads
  • ● Inverter and converter pads
  • ● Sensor thermal pads
  • ● Electronic control unit pads
  • ● Flame-retardant silicone thermal components
  • ● Sealing and thermal hybrid components

Electronics & Sensors

For electronics manufacturers, we support custom thermal pads used between heat-generating components and housings or heat sinks.

Typical applications include:

  • ● PCB thermal interface pads
  • ● Waterproof electronics housings
  • ● Sensor modules
  • ● LED lighting
  • ● Industrial controllers
  • ● Telecom devices

Industrial Equipment

For industrial systems, we produce silicone components where heat transfer, sealing and repeatability are important.

Typical applications include:

  • ● Power supply modules
  • ● Motor control systems
  • ● Thermal gaskets
  • ● Control cabinets
  • ● Pumps, valves and fluid control devices

Quality and Inspection

We manufacture thermal pads for production environments where consistency matters. Inspection can be configured according to part requirements and customer specifications.

Inspection focus may include:

  • ✓ Thickness
  • ✓ Length and width
  • ✓ Hole diameter and position
  • ✓ Surface condition
  • ✓ Flash and burrs
  • ✓ Hardness
  • ✓ Color
  • ✓ Compression behavior
  • ✓ Visual defects
  • ✓ Packaging and labeling

For critical applications, we can review inspection plans during the quotation and validation stages.

Information Needed for a Thermal Pad RFQ

To quote your project quickly and accurately, please send as much of the following as possible:

Drawing or 3D file

PDF, STEP, IGES, DXF or CAD file

Dimensions

Length, width, thickness, holes, slots, tolerances

Material requirement

Thermally conductive silicone grade or target properties

Thermal conductivity

Required W/m·K if specified

Hardness

Shore A target or compression requirement

Operating environment

Temperature, chemicals, outdoor exposure, flame rating

Electrical requirement

Dielectric insulation or conductive requirement

Surface requirement

Tack, matte, textured, liner, adhesive backing if needed

Quantity

Prototype volume and annual production demand

Application

Heat source, heat sink, compression condition, assembly method

Validation requirement

Samples, PPAP, testing or inspection requirements if applicable

If you do not have a final material selected, we can review the application and recommend a suitable direction.

Request a Thermal Pad RFQ

Send us your drawing, 3D file or application details, and we will review manufacturability, material options, tooling approach and production feasibility.

For faster quotation, include:

  • ✓ Part drawing or CAD file
  • ✓ Required quantity and annual forecast
  • ✓ Target material or performance requirements
  • ✓ Thickness and tolerance requirements
  • ✓ Application environment
  • ✓ Expected project timeline

LSRParts manufactures custom thermal pads and thermally conductive silicone components for OEM production programs. Contact us to start your RFQ.